Gear review: Combat Application AR-cleaning tool

Recently, I ran in a four-mile rifle/pistol event in under a 95-degree west Texas sun.  My feet kicked up powder-fine dirt the entire way.  At least, I thought, I wouldn’t have mud to clean up.  I was wrong in a way, where it came to my poor AR, which took the brunt of dripping sweat and the centuries-old powdered sand all around.  When I uncased back home, there was “mud” on the outside and hard-packed grit – the worst I’ve seen – in and around the bolt carrier group. As I sat at my table cleaning the gunk off, it occurred to me to share the best tool ever for this job.  Enter the Combat Application Tool (CAT).

the_cat_is_bolt_cleaner_extraordinaire

The CAT is bolt cleaner extraordinaire. (Photo: Eve Flanigan)

The CAT was originally recommended via an associate whose friend said it was the greatest AR cleaning device ever.  Since that friend has seen more than his share of action in more than one sandbox, I took that recommendation and ordered the then-little known gadget from its developer in Wyoming.

Since then, the little tool has proven itself useful beyond compare in removing carbon build-up from those difficult places and angles on AR innards.  Someone knew what they were doing when they designed this small, but heavy-duty device.

the_quarter-inch_hex_head_is_a_little_big_for_my_bit_but_you_get_the_idea

The quarter inch hex head is a little big for my bit but you get the idea. (Photo: Eve Flanigan)

My firing pin was caked with hardened carbon around the base. The stuff wouldn’t budge with a cleaner-lubricant-protectant (CLP ) soaked rag.  CAT to the rescue – dropping the pin into its cloverleaf-shaped aperture, a couple twists and the stuff had loosened substantially.  A couple more, with added pressure from me, and it was shiny after a wipe-down.   Parts of the pin itself bore buildup as well.  These spots were scraped off by simply pulling the pin through the same aperture at an angle.  The finely-ground stainless steel edge of the CAT made short work of the mess without etching the pin.

thread_a_patch_through_the_slot_at_the_top_for_those_hard-to-reach_spaces

Three a patch through the slot at the top for those hard to reach spaces. (Photo: Eve Flanigan)

The bolt was a sight to be seen, with a thick crust of carbon and dirt caked onto the funnel-shaped curve on the rear of the bolt.  Again, CLP did nothing and I worried for a moment I’d burned stuff right onto my bolt.  This is where the CAT really shines.  Its forked end is made for just this job, its curves cut to match a mil-spec M4 bolt.  Some bolts may require a little more wiggling to rotate the tool around the bolt’s exterior, but the jigsaw-like match is guaranteed to clean the bolt to “tactical tolerances” as the manufacturer puts it.  In seconds, it was clean enough for more use. With a couple minutes of effort, the bolt looked like new again.

bye_bye_carbon_buildup-jpg

Bye-bye, carbon buildup… (Photo: Eve Flanigan)

The CAT also makes swabbing out the carrier a breeze.  It’s outfitted with a slot for threading a patch through. Several random sizes of t-shirt “patches” can be cut to swab the sides or narrow end of the carrier.

One feature I haven’t used is the ¼-inch hex head slot. If your bits fit the aperture, the CAT becomes a high-leverage driver in addition to its other functions.

and_the_gunk_on_the_side_of_the_firing_pin-_it_does_not_however_clean_fingernails

…And the gunk on the side of the firing pin. It does not however clean fingernails. (Photo: Eve Flanigan)

This tool is one of the handiest I own for gun maintenance.  It comes in a slim folder, with pictorial instructions to remind the user how it works.  It’s made of stainless steel weighs under two ounces. That bit of weight feels solid in the 3.5 inches of space it occupies.

In addition to the 5.56 size, the Combat Application Tool is available in a 7.62 model for the AK platform users.

the_firing_pin_cleaning_slot_cleans_the_base

The firing pin cleaning slot cleans the base. (Photo: Eve Flanigan)

The CAT is still made in the USA, but apparently is now sold only through dealers. LaRue Tactical is one, and they’re selling it for a buck less than the $35 I paid several years ago. That’s a great value for the headaches and time saved getting your rifle really clean.

Source Article from http://www.guns.com/review/gear-review-combat-application-ar-cleaning-tool/

SHARE
This article was syndicated from Guns.com Guns.com is a niche news web site that publishes original reporting on the wide range of topics within the gun world. We publish Monday through Saturday. Our approach is to explore the topic of guns through the widest lens possible, to deliver these findings as fairly and accurately as possible and to host the opinions and perspectives of our writers and readers as selflessly as possible, trying our best not to get in the way of our contributors. Our desire is to allow our writers and readers to tell their stories, no matter what the story is, as long as we believe a) it will benefit or interest gun owners and b) conforms to ethical journalistic methods and practices. Our headquarters are in Illinois but our contributors submit to us from across the United States — from Maine to California, from Texas to Alaska and every state in between.